Skip to content

Repair cost · one wheel

Wheel Bearing Replacement cost

Expect about $250-$650 at an independent shop, or $290-$740 at a dealer, for a mainstream vehicle. Your state, vehicle and shop move that number, set them below.

EstimateData reviewed November 2026How we calculate

Disclosure: this site is supported by advertising and affiliate links. We may earn a commission if you buy through a link, at no cost to you. It never changes our estimates. Read our affiliate disclosure.

National estimate
$250-$650
Independent shop
Parts
$80-$300
Aftermarket to OEM
Labor
1.2-2.5 hr
At $140/hr baseline
DIY difficulty
3/5
Intermediate

Calculator

Wheel Bearing Replacement calculator

04Shop type

Covers one wheel. Parts and labor only. Taxes, shop fees and diagnostics are extra.

Wheel Bearing Replacement, National average, Average vehicle: estimated $250 to $650.

Estimated total · National average

Estimate

$250to$650

Against the national average

This is the national figure. Pick your state and the needle shows how local labor rates move it.

Where the money goes

58% labor

Parts
$80-$300
Labor
$170-$350

How this number is built

( parts $80-$300 + 1.2-2.5 hr × $140/hr ) × 1.00 vehicle factor

What wheel bearing replacement involves

Wheel bearings let each wheel spin freely while carrying the vehicle’s weight. A worn bearing gets steadily louder and, if ignored, can fail badly enough for the wheel to lock or separate.

What this estimate covers: One bearing or hub assembly and installation. Bolt-on hub assemblies sit at the low end for labor; press-in bearings take longer.

Show the math

How we get this number

The national figure, step by step. Nothing else goes into it: no dealer feeds, no hidden adjustments.
Parts
$80-$300
Editorial range, aftermarket to OEM
Labor hours
1.2-2.5 hr
Typical: about 1.5 hr
Labor rate
$140/hr
National baseline, independent shop
Vehicle factor
×1.00
Mainstream vehicle (baseline)

( $80-$300 + 1.2-2.5 hr × $140 ) × 1.00

= $250 to $650

Low end = lowest parts + fewest hours. High end = highest parts + most hours. Each part rounded to the nearest $5.

Parts ranges and labor hours are editorial estimates; labor rates are modeled from published data. Sources and limitations.

Wheel Bearing Replacement cost by state

Estimated wheel bearing replacement cost in all 50 states and DC for a mainstream vehicle. Only labor changes between states; the parts range is the same. Select a state for its full labor-rate breakdown.
Estimated wheel bearing replacement cost by state
StateIndependentDealer
National average$250-$650$290-$740
Alabama$230-$615$265-$690
Alaska$250-$650$290-$740
Arizona$250-$650$290-$740
Arkansas$225-$600$260-$675
California$270-$700$320-$800
Colorado$250-$650$290-$740
Connecticut$255-$665$295-$750
Delaware$250-$650$290-$740
District of Columbia$265-$690$315-$790
Florida$255-$665$295-$750
Georgia$240-$640$285-$725
Hawaii$260-$675$310-$775
Idaho$235-$625$280-$715
Illinois$250-$650$290-$740
Indiana$235-$625$280-$715
Iowa$230-$615$265-$690
Kansas$230-$615$265-$690
Kentucky$230-$615$265-$690
Louisiana$230-$615$265-$690
Maine$240-$640$285-$725
Maryland$255-$665$295-$750
Massachusetts$260-$675$310-$775
Michigan$235-$625$280-$715
Minnesota$250-$650$290-$740
Mississippi$225-$600$260-$675
Missouri$235-$625$280-$715
Montana$230-$615$265-$690
Nebraska$230-$615$265-$690
Nevada$240-$640$285-$725
New Hampshire$255-$665$295-$750
New Jersey$260-$675$310-$775
New Mexico$230-$615$265-$690
New York$260-$675$310-$775
North Carolina$235-$625$280-$715
North Dakota$230-$615$265-$690
Ohio$235-$625$280-$715
Oklahoma$230-$615$265-$690
Oregon$255-$665$295-$750
Pennsylvania$240-$640$285-$725
Rhode Island$250-$650$290-$740
South Carolina$235-$625$280-$715
South Dakota$230-$615$265-$690
Tennessee$235-$625$280-$715
Texas$240-$640$285-$725
Utah$240-$640$285-$725
Vermont$240-$640$285-$725
Virginia$250-$650$290-$740
Washington$260-$675$310-$775
West Virginia$230-$615$265-$690
Wisconsin$235-$625$280-$715
Wyoming$230-$615$265-$690

Signs you need wheel bearing replacement

  • Humming, growling or droning that rises with speed
  • Noise that changes when you steer left or right
  • Play or looseness when the wheel is rocked by hand
  • ABS warning light (the sensor is often built into the hub)
  • Uneven tire wear

How long does wheel bearing replacement take?

About one to two and a half hours per wheel.

Shops bill from a labor guide rather than a stopwatch: typically 1.2-2.5 hours for this job, most often around 1.5. Can you keep driving? An early hum is not an emergency, but a bearing that grinds or has play is unsafe. Fix it promptly.

DIY vs. shop

Do it yourself

Intermediate 3/5

Bolt-on hubs are a moderate DIY job with a big breaker bar and a torque wrench for the axle nut. Press-in bearings need a hydraulic press.

Parts only: $80-$300

At a shop

$250-$650

Of which labor: $170-$350

What pushes a quote up

  • Press-in bearings versus bolt-on hub assemblies
  • Seized hubs in rust-prone regions
  • Integrated ABS sensors

Before you approve the quote

FAQ

Wheel Bearing Replacement cost: FAQ

How much does wheel bearing replacement cost?

We estimate $250-$650 at an independent shop and $290-$740 at a dealer for a mainstream vehicle (one wheel). That is $80-$300 in parts plus 1.2-2.5 hours of labor at a national baseline of $140 per hour. It is an estimate, not a quote.

How long does wheel bearing replacement take?

About one to two and a half hours per wheel. Shops typically bill 1.2-2.5 labor hours for this job.

Can I drive my car if it needs wheel bearing replacement?

An early hum is not an emergency, but a bearing that grinds or has play is unsafe. Fix it promptly.

Can I do wheel bearing replacement myself?

We rate it intermediate (3 out of 5). Bolt-on hubs are a moderate DIY job with a big breaker bar and a torque wrench for the axle nut. Press-in bearings need a hydraulic press.

Why does wheel bearing replacement cost more in some states?

The parts cost about the same everywhere; labor does not. Using our state labor-rate estimates, the same job runs about $225-$600 in Arkansas and $270-$700 in California at an independent shop.

What makes a wheel bearing replacement quote higher than this estimate?

Common reasons: press-in bearings versus bolt-on hub assemblies; seized hubs in rust-prone regions; integrated ABS sensors. One bearing or hub assembly and installation. Bolt-on hub assemblies sit at the low end for labor; press-in bearings take longer.

Related repairs